Masonry Water Repellent (Water Base) - BS 16

Masonry Water Repellent BS 16

Product description:

Pitturalia® BS 16is a one component, VOC compliant, penetrating water repellent which contains a proprietary modified siloxane. This water-based siloxane penetrates most masonry and concrete pores and capillaries up to ¼ inch or more depending on surface porosity and moisture content at the time of application.

Pitturalia® BS 16reacts with the silica in concrete and masonry in the presence of ultraviolet light and atmospheric moisture. This reaction forms strong permanent bonds beneath the surface and creates a hydrophobic zone that prevents water molecules from penetrating, while allowing free migration of water vapors. The chemical bonds formed in this process allowPitturalia® BS 16to become integral part of the substrate and provide long-term water repellent protection.

Application:

Recommended surfaces include: architectural precast or cast in place, concrete, brick, mortars, natural stones, limestone, granite, sandstone, terra cotta, ceramic tile and grout, adobe, exposed aggregate products, Portland cement stuccos, plaster and concrete masonry units.

Protects horizontal surfaces such as pavements, sidewalks and plazas. It should also be used on vertical surfaces with leaks and or where extra protection is desired.

Also protects bridges, parking decks, airport taxiways and aprons, piers and marine structures, and other surfaces requiring outstanding corrosion resistance and protection from chloride penetration.

For use on brick masonry to protect against the entrance of wind-driven rain.

To reduce the effects of mildew, efflorescence, and stains from concrete and masonry.

Advantages:

Effective on most vertical or horizontal exterior, above-grade masonry surfaces. Natural substrate color and surface textures are unaffected, with little to no gloss created.

Benefits of this product are:

-Excellent resistance to water intrusion

-Deep penetration into the substrate

-Exhibits good beading effects

-100% water vapor permeable

-Mildew and fungus resistant

-Efflorescence protection

-High resistance to alkali attack

-Freeze thaw protection

-can be reapplied to treated surfaces

Chemical Products' state-of-the-art protective treatments have developed a reputation by architects and building professionals as the premier solution for water repellents and sealers. Chemical Products' is dedicated to solving the destructive influence water intrusion and other elements have on building materials.

Appearance:

Pitturalia® BS 16is clear, non-yellowing and does not change the color or appearance of typical surfaces to which they are applied. Buildings and structures stay cleaner because conditions which contribute to staining are reduced and dirt rinses away more readily.

Pretreatment for Paint:

Water can penetrate through most paints and coatings. This leads to damp substrates and blistering and peeling of paint. Treat concrete, masonry, or stucco withPitturalia® BS 16prior to painting keeps walls drier and extends the life of the paint. CP-500W™ is compatible with most latex and other paints. But to assure compatibility between paint and pretreatment, a small test application is recommended.

Note:Do not usea pretreatment or allow overspray on metal or other nonporous surfaces to be painted.

Limitations:

Not intended for below-grade waterproofing.Pitturalia® BS 16will leave a residue on non-porous substrates such as glass windows, metal frames and painted surfaces. Caution should be taken with specialty coated glass or plastic windows.

Check compatibility before application. Protect materials which can be damaged by solvents. Do not apply when following conditions are present:

- Ambient or surface temperature less than 40° F or predicted to fall below 40° F within 24 hours following application.

- Rain within 72 hours prior to application or predicted within four hours after application.

- Wet or frozen substrates.

- High winds which could cause excessive overspray.

Application should be completed by qualified applicator with experience applying water repellents. Application equipment should be clean and free of foreign materials which could be dissolved and deposited on surfaces to be treated. Contact Pitturalia team for additional precautions and information on compatibility with specific materials.

Installation:

Best results are obtained by applyingPitturalia® BS 16on clean and dry substrates. All surfaces must be cleaned to remove all traces of dirt, dust, efflorescence, mold, salt, grease, oil, asphalt, laitance, curing compounds, paint, coatings and other contaminants. Acceptable surface cleaning methods include shot blasting, sandblasting, water blasting and chemical cleaners. If chemical cleaning agents are used, neutralize and wash off residues completely. Allow surface to dry at least 72 hours after water cleaning. Check with your Chemical Products Industries, Inc. representative to verify suitable cleaning methods, products and that the surface preparation is adequate.

As a standard procedure, fresh concrete should be allowed to dry for 28 days before application. All repainting must be completed and allowed to cure at least 3 days. Concrete repair and replacement must be completed prior to application. Patching materials, caulking, sealing materials, traffic paint must be fully cured before applyingPitturalia® BS 16. In addition, the actual amount of material that is used for each application is dependent on the absorptive capacity of the substrate.

Before applying, it is recommended that preliminary tests be carried out to determine usage and to test the effectiveness of the treatment.

Application:

Apply water repellents as early as practical to protect substrates during construction, but not before wall cap, flashings, and roof are in place and water trapped in structure has been drained.

Spray applyPitturalia® BS 16by low-pressure (150 psi maximum) pumping equipment with a wet fan type spray nozzle. Alternate methods include nap roller (1”) or by brush. Required application rate varies from 70 to 175 sq. ft. per gallon depending on surface texture and absorbency.

Vertical Surfaces:

Mix well before using. Test small area before starting general application to assure desired results and coverage rates. Apply when surface and air temperatures are between 40°F to 110°F. Provide adequate ventilation.

Apply in a flooding application, from the bottom up so the material runs down 6 to 8 inches below the spray pattern.

On horizontal surfaces the liquid material should pond on the surface at least 5 seconds before being absorbed. For best results two applications are recommended with the second application applied using a wet on wet technique, retreat within three to five minutes after initial application. A wet treated surface may be agitated with a soft bristle scrub brush to ensure more even distribution and greater penetration. During application, precautions should be taken to protect the surrounding area from overspray. Remove overspray from non-targeted surfaces immediately with soap and water. Apply to southern exposed areas during coolest part of the day.

Horizontal Surfaces:

Mix well before using. Pretest to measure material coverage rates. Apply enough material so that solution stands for 60 seconds before completely penetrating the surface. If additional material is required to reach desired coverage rate, a wet on wet application can be used. Avoid paddling or pending, brush or broom to spread material to more porous area. If applicable, block all drains and use absorptive coverings to contain run-off of excess material. To avoid unnecessary clean-up, use soap and water to remove overspray as soon as possible.

Caution:

Over application of material may cause darkening of surface.

Dry Time:To touch, or 2 to 6 hours depending on temperature and humidity.

Clean Up:Thoroughly rinse spray equipment with clean water. Wash rollers with soap and water. Rinse thoroughly.

Precautions:Fire hazards are eliminated sincePitturalia® BS 16is water-based and does not contain combustible or flammable solvents. Respiratory protection is not required during normal use and handling. Please refer to the Material Safety Data Sheet for more detailed information.

Warranty:

Five years when properly applied. Contact Chemical Products Industries, Inc. for information and warranty requirements.