Plugging King Waterproofing (E-6) - E-6

1.Quick-setting type - with water blocked, instantly sealing, 2.Slow-setting type--dampproof, anti-permeability, easy to paste - details see: https://www.buildingsupplieshub.com/plugging-king-waterproofing-e-6-10100429
Type: Other Waterproofing MaterialsPlace of Origin: Guangdong China (Mainland)Brand Name: EloktModel Number: E-6
Resistance osmotic pressure, Mpa,7d≥: 1.5Heat resistance,100°C,5h: No cracking, peeling and fall offBonding strength/MPa,7d≥: 0.6Advantages: Non-toxic, harmless, non-polluting
Quick type application scope: Buildings, pool, kitchen, subways and rapid plugging works.Slow type application scope: Large area surface,tiles, mosaics, marble block adhesive materia  
Plugging King Waterproofing (E-6)
contact supplier for Plugging King Waterproofing (E-6)


E-6 Plugging King

1.Quick-setting type --- with water blocked, instantly sealing

2.Slow-setting type--- dampproof, anti-permeability, easy to paste

"Plugging King" is the absorption of foreign advanced technology and retains the advantages of similar products at home and abroad, developed efficient inorganic waterproof plugging material, includes Slow-setting type (I type) and Quick-setting type (II type).

Key Features

• One component gray powder;

• Non-toxic, harmless, non-polluting;

• With water plugging, instant sealing, can be used on front and back surfaces;

• The strength development speed and compressive strength is the leading domestic level;

• Freezing time is adjustable: Instant plugging can use Quick-setting type, water impermeability paste using Slow-setting type.

Application Scope

Quick-setting type is used for all kinds of underground buildings or structures, cable channel, pool, kitchen and toilet, air defense caves, subways, tunnels and other rapid plugging works.

Slow-setting type used for large area surface treatment, is the main choice material to paste tiles, mosaics, marble block adhesive material, which can waterproof and paste once.

Executive standard:GB 23440-2009

No.

Test item

Slow-setting typeQuick-setting type
III

11

Setting time

initial set/min

≥10≤ 5
final set/h≤36010

2

Compressive strength

/MPa

1h≥---4.5
3d≥13.015.0

3

Breaking strength/MPa

1h≥

---1.5
33d≥3.04.0

4

Difference values of Resistance osmotic pressure,Mpa,7d≥coating0.4---
Resistance osmotic pressure, Mpa,7d≥test-piece1.51.5
5Bonding strength/MPa,7d≥7d ≥,0.60.6
6

Heat resistance,100°C,5h

No cracking, peeling and fall off

7

Cycle of freezing and thawing(-15°C~+20°C),20 times

No cracking, peeling and fall off

Construction Tools

Cleanup primary tools: hammers, chisels, wire brooms, rags

Weighing and batching tools: scales, mixing bucket (basin), buckets, hand blender

Coating tools: scraper, trowel, brush, pressure sub-

Plugging tools: different diameter stick

Maintenance tools: sprinkler, water bucket (basin), brushes

Quick-setting plugging king construction method

First, plugging leaks mouth

1. The leaking joints should be chiseled "V" shaped, the base layer should be clean, solid and dense.

2. Put plugging king: water = 1:0.3 ~ 0.35 into mixing basin (buckets), mixing into a paste (add more water, the setting time is longer) .When the temperature is below 10°C, stirred quickly with warm water (about 40°C). The ingredients should not be made too much once, so as to avoid solidification;

3. Squeezing the material to "V" shaped groove or leaking cracks when the slurry slightly hot and hard, blocking with a wooden stick;

4. For seepage pits, directly put into plugging king, and then compacting, troweling and watering conservation;

5. For serious leaking cracks, using the drainage method, first block the upper gap, and then block under gap. Perforates a hole to reduce pressure and lead the leakage water.

6. For a large area ofleakage, if necessary, perforates a hole to lead the water. First plugging holes, and then plugging the large leaking area;

7. Curing time is about 2 to 3 days, watering, covering wet materials, or maintenance.

When in a moist environment such as basement or in a hardening waterproof layer, make the protective layer immediately or paste some material, which need not wet curing.

Second, seepage surface treatment

1.The base course must be wet, solid and clean, mixing plugging king with two times the weight of the sand on rough place.

2. Mix plugging king: water = 1:0.3~0.35 with a mechanical stirrer for about 2 minutes (without pellets, a fine putty-like slurry), the ingredients should not be made too much once, so as to avoid waste.

3. Construction: 2 to 3 times, coating the prepared slurry on a water surface. After the first layer to be hardened (no finger pressure traces), apply a second layer. If there is a large area ofwater seepage, apply the third layer. If only partial leakages, then coated a layer at seepage place until it does not leak. Each scraping must be back and forth a few times, make coverage dense between the coatings. Each with a quantity about 1.2kg/m2, the total thickness is about 1.5 ~ 2.2mm.

King Construction Method

1.Ingredients: plugging king is suitable for no water seepage surface, plugging king: water = 1:0.3 ~0.35 with a stirrer for about 2 minutes, then become a fine putty-like slurry without pellets.

2. Construction methods: use with a trowel or scraper coating the first layer, after hardening, wet (no water), coating the second layer. Scraping must be back and forth a few times, make coverage dense between the coatings. Each with a quantity about 1.2kg/m2, the totalthicknessis about 1.5 mm.

3. Conservation methods (according to quick-setting type).

Paste the bulk of the construction decoration

Protective layer and the decorative layer block material can be carried out directly on the waterproof layer. Mixing slow-setting plugging king with water can be used as a waterproof tile adhesive. Decorative block (tile, marble, granite, paste should be soaked before paste, which need not wet curing).

Project acceptance

1. The checked waterproof layer should without hollowing, cracking, loss and chalking;

2. Do water storage test, it should be carried out after hardening of waterproof layer;

3. The thickness of waterproof layer should meet the design requirements;

4. For humid environments acceptance, if the coating surface still have drops, moisture condensation should take into account. If for this reason, it will disappear naturally after dry.

Packaging, storage, shelf life

This product uses the double plastic sealed package, the basic package specifications: 1kg, 5kg. The outer packaging uses cartons or paper bags. The material is easy to damp. To prevent breakage bags should be stored in a dry room. The shelf life is six months; the extended product should be tested before use, so as not to affect the results.

Pictures for your reference

Related Product for Plugging King Waterproofing (E-6)